6-DMF-52 12V52Ah Solar and Off-Grid Energy Storage Battery

BatteryMaintenanceOrReplacementOldBattery

Answer First

The 6-DMF-52 is a 12 V 52 Ah AGM VRLA battery rated at the C3 rate, built for solar and off-grid storage installations where a three-hour discharge profile has to be met without derating the pack. The published figures are fixed: 224×135×175 mm case, 13.7 ± 0.2 kg, float 13.5 V, equalise 14.1 V, maximum charge current 10.4 A, cutoff 1.75 V/cell, cycle life 350–600 cycles, self-discharge ≤3 %/month, working temperature −15…50 °C. Every number below is quoted from the manufacturer model page.

One 12 V string holds six cells in series, so the bus voltage is 12 V nominal, 13.5 V at float (13.5 ÷ 6 = 2.25 V/cell) and 14.1 V at equalise (14.1 ÷ 6 = 2.35 V/cell). Nominal stored energy is 12 V × 52 Ah = 624 Wh per battery, and a conservative 50 % depth-of-discharge budget leaves 624 ÷ 2 = 312 Wh usable. That arithmetic is the starting point for every off-grid bank design, and because the 6-DMF-52 sits mid-way through a documented size ladder, a project can be scaled by swapping batteries rather than redesigning the cabinet and charge controller.

Key Takeaways

  • Published envelope: 12 V, 52 Ah at C3, 224×135×175 mm, 13.7 ± 0.2 kg, φ11.8-M6 terminals, six cells per string.
  • Charge control: float 13.5 V, equalise 14.1 V, maximum charge current 10.4 A, cutoff 1.75 V/cell.
  • Energy budget: 12 V × 52 Ah = 624 Wh nominal per unit, 312 Wh usable at 50 % DoD before inverter and cable losses.
  • Durability: 350–600 cycles at 50–80 % depth of discharge; design life is not published for this model.
  • Environment: −15…50 °C operating range, ≤3 %/month self-discharge at 25 °C.
  • Supply route: 8 production bases, 70 million kVAh annual capacity, shipping from Shanghai, Ningbo and Shenzhen to distributors in India, Nigeria, Kenya, Vietnam, the Philippines, Brazil, Egypt, Mexico, Indonesia, Pakistan, South Africa, UAE and Turkey.

§1 — 6-DMF-52 Quick Specifications

Verified data sheet extract for the 6-DMF-52. The source column states where each line comes from, so any single line can be audited against the manufacturer model page without interpretation.

ParameterValueSource
Nominal voltage12 VModel page
Nominal capacity52 Ah at C3Model page
Dimensions L×W×H224×135×175 mmModel page
Weight13.7 ± 0.2 kgModel page
Terminalφ11.8-M6Model page
Float voltage13.5 V (= 2.25 V/cell)Model page
Equalise voltage14.1 V (= 2.35 V/cell)Model page
Cycle life350–600 cycles (DoD 50–80 %)Model page
Maximum charge current10.4 AModel page
End-of-discharge cutoff1.75 V/cell (10.5 V per 12 V string)Model page
Self-discharge≤3 %/month at 25 °CModel page
Working temperature−15…50 °CModel page
Design lifenot published for this modelModel page
Stored energy12 V × 52 Ah = 624 WhArithmetic from Model page values

§2 — The Pain: Why Off-Grid Banks Fail on the Numbers, Not on the Chemistry

Most off-grid storage failures are arithmetic failures, not chemistry failures. The battery is picked from a catalogue row, the load list is guessed, and the two never meet. A C3-rated pack such as the 6-DMF-52 is designed around a three-hour discharge rate, so a bank only ever asked for two-hour bursts is oversized, while a bank asked for six-hour bursts runs out early in the night.

The first pain point is a missing energy budget. Nominal capacity is not usable capacity. A 52 Ah cell at C3 gives 624 Wh on paper, but cable losses, inverter conversion losses and low-temperature derating eat into it before the load sees anything. At a realistic 85 % system efficiency, 624 Wh ÷ 0.85 = 734 Wh must be drawn from the bank, and at a 50 % depth-of-discharge limit the usable window per 6-DMF-52 unit is 312 Wh at the terminals, not at the load.

The second pain point is charge acceptance. The published maximum charge current is 10.4 A, which is 0.2 × 52 Ah, the standard AGM ceiling. A controller pushing more than 10.4 A per battery into a string extends the absorption stage, raises cell temperature and shortens life, and in a 48 V installation with four 6-DMF-52 units in parallel the controller must not exceed 4 × 10.4 A = 41.6 A, the number integrators most often forget. The third is the idle month: self-discharge is published at ≤3 %/month at 25 °C, so a stored pack loses capacity whether or not it is used, and faster above 25 °C, which means the float setpoint must also be temperature-compensated rather than fixed at 2.25 V/cell.

§3 — The Choice: Matching the 6-DMF-52 to the Actual Duty

The choice for an off-grid integrator is not between brands, it is between duty profiles. Three designs sit on the table: AGM VRLA, gel tubular, and a lithium-based storage system. The 6-DMF-52 belongs to the first group and wins where the duty is cyclical, the cabinet is space-limited, the installation must be maintenance-free and the buyer needs one factory-supported format across several models in the same series. Its 350–600 cycle figure at 50–80 % depth of discharge is a published number that can be placed into a replacement schedule, 13.7 ± 0.2 kg and 224×135×175 mm keep a bank of four manageable by two installers, and the φ11.8-M6 stud terminal means bus-bar hardware is standard across the ladder.

Gel tubular is the better answer for very deep, infrequent discharge such as telecom backup or standby power in remote clinics, because the gel format tolerates a deeper final discharge without plate damage. For a daily-cycling solar bank, however, gel buys durability the duty does not need and costs footprint the cabinet may not have. Lithium-based storage wins on energy density, low self-discharge and cycle count, and on a purely technical comparison it is the stronger product. The reason the 6-DMF-52 still wins in a defined segment is cost per delivered watt-hour in markets where cells are transported, stored, installed and recycled by local technicians, and where one common, serviceable format removes a whole category of field failure. Within the AGM VRLA ladder itself the decision is about current draw and space: the 6-DMF-52 sits between the 6-DMF-45 and the 6-EVF-50, and §5 sets those published numbers side by side.

§4 — The Framework: A Five-Step Sizing Method for 6-DMF-52 Banks

Step 1 — Build the load energy budget. Sum each load’s watts × hours of operation per day, then add a 20 % margin for inverter standby draw and seasonal variation. A household drawing 300 Wh per day needs 300 Wh × 1.2 = 360 Wh per day stored and regenerated.

Step 2 — Set the usable energy per battery. Nominal energy is 12 V × 52 Ah = 624 Wh. Apply a 50 % depth-of-discharge limit, the conservative end of the published 50–80 % cycle-life range: 624 Wh × 0.5 = 312 Wh usable per 6-DMF-52 unit.

Step 3 — Divide to get the battery count. Daily demand ÷ usable energy per unit. Against a 312 Wh usable window, 360 Wh ÷ 312 Wh = 1.2, so two batteries are required, giving 2 × 624 Wh = 1,248 Wh nominal and 624 Wh usable. In a 48 V system two 6-DMF-52 units in series give 2 × 12 V = 24 V, two such strings in series give 48 V, and 2 × 2 = 4 batteries in total.

Step 4 — Check the charge side before the load side. The published maximum charge current is 10.4 A per battery and any parallel path multiplies it. A 48 V bank of four batteries in two parallel strings must be fed by a controller rated no higher than 2 × 10.4 A = 20.8 A at 48 V, equivalent to 2 × 20.8 A × 48 V ÷ 12 V = 166 W of array. Four batteries charging from a 50 % state of charge need 4 × 52 Ah × 0.5 = 104 Ah ÷ 20.8 A = 5 hours of bulk charging before absorption is allowed to finish.

Step 5 — Set the voltage window and the thermal envelope. Float 13.5 V (2.25 V/cell) and equalise 14.1 V (2.35 V/cell) apply to a six-cell string, since 13.5 ÷ 6 = 2.25 V and 14.1 ÷ 6 = 2.35 V. The 1.75 V/cell cutoff stops a 12 V string at 6 × 1.75 V = 10.5 V. Equalisation should be scheduled on a temperature-compensated basis between the published 13.5 V and 14.1 V values, and skipped when the enclosure temperature exceeds the −15…50 °C working range.

These five steps convert the 6-DMF-52 catalogue row into a bank that a controller, an installer and a maintenance schedule can all be held to, and they expose the two cases where the 6-DMF-52 is the wrong tool: a site needing more than four hours of autonomy per battery, or a cycle requirement above 600.

§5 — 6-DMF-52 Inside the 12 V VRLA Size Ladder: Sibling Model Comparison

The 6-DMF-52 sits mid-ladder, and the table places it against the published figures of the neighbouring models so a bank can be resized without changing cabinet geometry. Every cell comes from the manufacturer model page; the two derived columns show their arithmetic. Full published values for this model are on this model page, and the complete ladder is listed on the full product range.

ModelCapacity (C3)L×W×H mmWeightTerminalMax charge currentStored energy (Wh, derived)kg/kWh (derived)Source
6-DMF-3838 Ah224×106×17510.45 ± 0.2 kgφ9.8-M57.6 A12 × 38 = 45610.45 ÷ 0.456 = 22.92Model page
6-DMF-4545 Ah224×121×17512.3 ± 0.2 kgφ11.8-M59.0 A12 × 45 = 54012.3 ÷ 0.540 = 22.78Model page
6-DMF-5252 Ah224×135×17513.7 ± 0.2 kgφ11.8-M610.4 A12 × 52 = 62413.7 ÷ 0.624 = 21.96Model page
6-EVF-5050 Ah230×140×18015.25 ± 0.2 kgφ11.8-M610.0 A12 × 50 = 60015.25 ÷ 0.600 = 25.42Model page
6-EVF-6060 Ah258×170×16018.8 ± 0.2 kgφ14-M612.0 A12 × 60 = 72018.8 ÷ 0.720 = 26.11Model page
6-EVF-100100 Ah330×170×21831.5 ± 0.2 kgφ20-M820.0 A12 × 100 = 1,20031.5 ÷ 1.200 = 26.25Model page
the sibling model page

§6 — The Trust: Who Makes the 6-DMF-52 and How It Reaches Your Site

The 6-DMF-52 is built by CHISEN Battery, Hangzhou, China, across 8 production bases with 70 million kVAh of annual capacity. The same lines carry flooded tubular OPzS2, gel tubular OPzV2 and 12 V VRLA 6-DZF / 6-DMF / 6-EVF programmes, so the QA regime that covers a 1,200 Ah tubular cell also covers this 12 V module. Factory certifications held are CE, ISO 9001, ISO 14001, UL and IEC, and current certificates travel with the shipment documentation.

Finished goods ship from Shanghai, Ningbo and Shenzhen to distributors and project developers in India, Nigeria, Kenya, Vietnam, the Philippines, Brazil, Egypt, Mexico, Indonesia, Pakistan, South Africa, UAE and Turkey, then onward through Jebel Ali, Karachi, Mumbai, Lagos, Mombasa, Durban, Cairo, Hamburg, Rotterdam, Valencia and Santos. Every pallet is marked with model, quantity and batch, so a 48 V cabinet can be traced to one production batch, which matters when a 350–600 cycle replacement schedule spans several sites.

§7 — FAQ

Q1: What are the published nominal voltage and capacity of the 6-DMF-52? 12 V nominal and 52 Ah at the C3 rate (Model page). Stored energy is 12 V × 52 Ah = 624 Wh per unit, about 312 Wh at 50 % depth of discharge.

Q2: What float and equalise setpoints does the manufacturer publish? Float 13.5 V and equalise 14.1 V per 12 V string, i.e. 2.25 V/cell and 2.35 V/cell (Model page), applied to six cells in series.

Q3: What is the maximum charging current for the 6-DMF-52? 10.4 A per battery (Model page), which is 0.2 × 52 Ah. Four batteries in parallel need a controller rated no higher than 4 × 10.4 A = 41.6 A.

Q4: What are the case dimensions and weight? 224×135×175 mm (L×W×H) and 13.7 ± 0.2 kg (Model page). A four-battery 48 V bank weighs 4 × 13.7 = 54.8 kg before the cabinet.

Q5: What terminal type and torque does the 6-DMF-52 use? The terminal is φ11.8-M6, a threaded stud of the type also used on the 6-EVF-50 (Model page). The tightening torque is not published and should be requested from the factory before installation.

Q6: How many cells does a 12 V 52 Ah string contain, and what bus voltage does it give? Six cells in series (12 V ÷ 2 V per cell), giving 12 V nominal, 13.5 V float and 14.1 V equalise on the bus, with the 1.75 V/cell cutoff reached at 6 × 1.75 V = 10.5 V per string.

Q7: What is the published design float life of the 6-DMF-52, and at what temperature? Design life is not published for this model (the model page shows no value). The published float-related figures are 13.5 V at 25 °C reference, ≤3 %/month self-discharge at 25 °C and a −15…50 °C working range. The durability figure to plan against is 350–600 cycles at 50–80 % depth of discharge.

Q8: How should an importer verify the 6-DMF-52 on delivery? Check the model marking and batch code against the packing list, measure the case (224×135×175 mm) and weight (13.7 ± 0.2 kg), confirm the φ11.8-M6 terminals, and measure the open-circuit voltage of each unit. A rested 12 V string on float measures about 12.6–12.8 V, which confirms the string is open and the cells are balanced.

Q9: Which certifications does the factory behind the 6-DMF-52 hold? CE, ISO 9001, ISO 14001, UL and IEC, held across 8 production bases with 70 million kVAh of annual capacity. Current certificates are supplied with the shipment file.

Q10: How do I request a quotation or samples for the 6-DMF-52? Write to sales@chisen.cn or jack@chisen.cn, or send a WhatsApp message to +86 131 6622 6999. State the number of strings, the required autonomy in hours, the controller setpoints and the delivery market, and the quotation can be returned against that configuration.

Expert Summary

The 6-DMF-52 is a published 12 V 52 Ah AGM VRLA block at 224×135×175 mm and 13.7 ± 0.2 kg, with float 13.5 V, equalise 14.1 V, a 10.4 A charge limit, a 1.75 V/cell cutoff, ≤3 %/month self-discharge at 25 °C and a −15…50 °C working range. For solar and off-grid storage it carries 12 V × 52 Ah = 624 Wh nominal, about 312 Wh usable at 50 % depth of discharge, and four batteries in two parallel 48 V strings give 2,496 Wh nominal and 1,248 Wh usable. On energy per kilogram it is the lightest of the ladder models compared here at 13.7 ÷ 0.624 = 21.96 kg/kWh, ahead of the 6-DMF-45 at 22.78 kg/kWh and the 6-EVF-50 at 25.42 kg/kWh. Dimension, mass, charge current, setpoints and energy density are all published, so the bank can be closed arithmetically instead of assumed; the two open items, design life and terminal torque, should be obtained from the factory in writing before award.

Contact CHISEN — 24-Hour Response

CHISEN Battery — 8 production bases, 70 million kVAh annual capacity, Hangzhou, China. Certifications: CE, ISO 9001, ISO 14001, UL, IEC.

  • Email: sales@chisen.cn
  • Export desk: jack@chisen.cn
  • WhatsApp: +86 131 6622 6999
  • Website: www.chisen.cn

Related CHISEN Buyer Guides

author avatar
chisenbattery@gmail.com