Tag: lead acid battery

• 

  OPzS2-1500 2V 1500Ah Flooded Tubular Battery: DC Plant Sizing Guide (2026)

An OPzS 2V 1500Ah flooded tubular battery is specified when a site needs a 48V plant of roughly 72 kWh nominal, expects a service life of more than ten years on float, and has a plant room where a technician can carry out water top-ups on a planned schedule. The OPzS2-1500 is the die-cast tubular flooded cell in the middle of the published CHISEN range: 1500Ah at the 10-hour rate, 275 × 210 × 795mm, 850mm over the terminals, 77.00kg, and a float design life of more than 20 years at 25°C under IEC 60896-11 and DIN 40736-1.

This guide works through how the cell is specified, how a 48V string is built around it, and what it actually costs over seven years compared with tubular gel, AGM VRLA and lithium alternatives. It is written for the engineer who will sign the acceptance certificate, and for the distributor who has to defend the specification to a utility or a telecom operator.

Answer First

A 48V DC plant built from 24 OPzS2-1500 cells in series stores 72 kWh nominal (24 × 2V × 1500Ah), floats at 53.5V (24 cells × 2.23V/cell) with −3mV/°C/cell compensation, and delivers about 36 kWh usable at a 50% depth of discharge to 1.80V/cell — which supports a 1.5kW continuous load for 24 hours; the cell is 77.00kg, publishes dimensions to ±2mm and a 300A maximum charging current, and its 16-model ladder from 100Ah to 3000Ah lets a plant room be designed around integer cell counts instead of parallel string sprawl.

Key Takeaways

• The published OPzS range covers 16 sizes from 100Ah to 3000Ah, stepping 100 / 150 / 200 / 250 / 300 / 350 / 420 / 500 / 600 / 800 / 1000 / 1200 / 1500 / 2000 / 2500 / 3000Ah, each published with length, width, height and weight to ±2mm.
• Float charge is 2.23V per cell at 25°C with −3mV/°C/cell compensation, equalising at 2.35V and cycling at 2.40–2.45V, with a maximum charging current of 0.20 × C10 A — 300A on the 1500Ah cell.
• The 1500Ah cell is the practical centre of the ladder. It stores 3 kWh per cell, so one 24-cell string gives 72 kWh — the size most often quoted for off-grid telecom plants, solar hybrid microgrids and MV/LV substation trip supplies where lead-acid remains the default technology.
• Flooded cells cost less than gel and carry less mass at the same capacity — the OPzS2-1500 weighs 77.00kg against 104.00kg for the OPzV2-1500, a saving of 27kg per cell and 648kg per string — but they buy that saving with a maintenance routine: planned water top-ups and a ventilation design that takes hydrogen generation seriously.
• Water top-up frequency is temperature-driven, not calendar-driven — roughly monthly in a hot plant room and considerably longer in a cool one — and it is the single operating habit that decides whether a flooded bank reaches its published design life.

Quick Specifications: CHISEN OPzS2-1500 at a Glance

Cell-level electrical and mechanical data for this model is published on the OPzS2-1500 product page, and the full 16-model series data sits on the OPzS flooded tubular battery range page.

The Published OPzS Range: 16 Models, 100Ah to 3000Ah

The Pain: Where 1500Ah Flooded Installations Actually Fail

Flooded tubular cells are the most forgiving chemistry in the substation and the least forgiving in the plant room. The failures are operational rather than electrical, and they repeat in the same order on every continent.

Water top-ups get deferred. A bank left without water loses capacity through grid corrosion long before the electrolyte level drops below the visible threshold. The interval is set at commissioning and never revisited, and it must be revisited, because the interval roughly triples for every 10°C drop in ambient temperature. A cell inspected monthly in a 35°C room in Accra or Ho Chi Minh City can need inspection weekly in a 15°C room in Warsaw.

Float voltage is set once and never re-checked. The published compensation of −3mV/°C/cell moves the float setpoint by 1.44V across a 24-cell string between 20°C and 40°C — 0.06V per cell multiplied by 24 cells over a 20°C swing. Set the rectifier once in August and the bank spends the winter undercharged and the summer overcharged, which is precisely the pattern that drives the gradual capacity loss operators attribute to the battery being old.

Ventilation is sized from the cell count, not from the gas rate. Flooded cells vent hydrogen under charge, and the EN 50272-2 method estimates gas volume as approximately 0.42 × I_gas × t litres per cell, where the gas current for a float-charged cell is commonly taken as 0.002 × C10 A. For a 1500Ah cell that is 3A per cell and about 1.26 litres per hour of gas per cell, so a 24-cell string generates roughly 30 litres per hour — 0.030 m³/h — and a two-string plant room roughly 0.060 m³/h. Undersized ventilation is a safety finding waiting for an inspection.

Rate-corrected capacity is ignored in the autonomy calculation. The 1500Ah rating is measured at the 10-hour rate to 1.80V/cell at 25°C. At the 3-hour rate the same cell typically returns around 160–190Ah less, and at the 1-hour rate considerably more is lost. A bank specified for 24 hours at a hard 1.5kW load will not deliver 24 hours in practice unless the autonomy table was built on rate-corrected figures.

Cells are mixed with VRLA in the same room. Flooded and sealed cells have different float currents, different gas behaviour and different failure signatures. Mixing them in one room without separate ventilation, separate alarm thresholds and a documented inspection regime makes every alarm ambiguous.

The Choice: String Arithmetic, Chemistry Trade-Off and 7-Year Cost

String and parallel configuration

Every OPzS cell is 2V, so the string length follows the DC bus and only the cell capacity and the parallel count remain as design variables.

An off-grid telecom plant outside Mombasa, a solar hybrid microgrid feeding a mining camp near Pucallpa in Peru and an MV substation trip supply outside Bloemfontein share a load profile of roughly 1.5kW continuous on a 48V bus:

• Nominal energy: 24 cells × 1500Ah = 36,000Ah, which is 72,000Wh per string.
• Usable at 50% DoD (1.80V/cell): 36,000Wh → 24 hours at 1.5kW.
• Usable at 80% DoD (2.00V/cell): 57,600Wh, provided the inverter undervoltage cutoff is set at or above 48.0V.
• Rectifier sizing: 1.5kW site load + 30A float current (2% of C10) + equalising reserve ≈ 3.5kW continuous, so a 4kW rectifier absorbs equalisation without starving the string.
• Parallel strings: two 24-cell strings give 144 kWh nominal, 48 hours at 50% DoD, and full redundancy while one string is isolated for maintenance.

7-year total cost of ownership, 48V / 72 kWh nominal site

Indicative 2026 mid-market pricing bands; actual quotations depend on volume, freight, certification scope and local duties.

The comparison is the argument for flooded tubular in a specific and defensible place: a site with a plant room that already has hydrogen ventilation and a technician on a routine visit cycle. It is not the right answer where the site is unattended, where the ambient temperature swings widely without compensation, or where the battery room cannot be ventilated to code — there the gel cell is the cheaper life-cycle answer, and lithium is the one to model carefully, including the DC bus changes, cooling and BMS integration.

Why 1500Ah is the practical centre of the ladder

Cell size drives three physical constraints at once, and at 1500Ah they align unusually well. A 275 × 210mm footprint fits a standard 210mm-deep rack tier, 77.00kg sits at the upper end of what two technicians should lift without mechanical aid, and the installed floor load of roughly 0.76kN per cell and 18.1kN per 24-cell string is a standard plinth specification for a plant room. Below 1000Ah the cells are short and the rack tiers are underused; above 2000Ah the cell height exceeds 770mm and the room loses headroom for the maintenance walkway.

The Framework: 7 Hard Metrics for Specifying a 1500Ah Flooded Tubular Cell

1. Rate-corrected capacity, not nameplate. Require Ah at the discharge rate the site will actually see, with the end voltage and temperature stated — a 1500Ah cell at the 3-hour rate typically returns 160–190Ah below the 10-hour figure, and the autonomy table must be built on the corrected value.
2. Float life at the real ambient temperature. The 20+ year design life is specified at 25°C. A containerised shelter in Windhoek, Kano or Lima with no air conditioning will not reach it without attention.
3. A ventilation design that starts from the gas rate. Calculate per EN 50272-2 using approximately 0.42 × I_gas × t litres per cell, with I_gas commonly taken as 0.002 × C10 A — 3A and about 1.26 L/h per 1500Ah cell, roughly 30 L/h for a 24-cell string — and confirm the room design with a qualified engineer.
4. Water top-up planning, costed and scheduled. Include deionised water, a measuring jug or hydrometer, PPE and technician time in the operating budget; set the inspection interval from ambient temperature, not from the last invoice.
5. Charge-voltage acceptance window and compensation. Float at 2.23V per cell (53.5V on a 24-cell string), equalising at 2.35V, cycling at 2.40–2.45V, maximum charge current 0.20 × C10 A = 300A, with temperature compensation actually enabled in the field configuration rather than only specified on the datasheet.
6. Mechanical fit and floor loading. Use the published geometry — 275 × 210 × 795mm, 850mm over terminals, 77.00kg for the 1500Ah cell — to confirm rack pitch, floor loading of roughly 0.76kN per cell and 18.1kN per string, and aisle width for a technician working with a hydrometer and a watering can.
7. Documentation at shipment, not after. Require the IEC 60896-11 and DIN 40736-1 conformity statement, batch date codes, a cell consistency procedure and a spare-cell allowance of 1–2% with the consignment.

The Trust: Buying Flooded Tubular Cells Without Buying Trouble

The most common commercial mistake is treating flooded and sealed tubular cells as interchangeable because the model numbers look alike. They are not the same product, and the difference shows up in maintenance cost rather than in the purchase order.

Ask for electrolyte specification, not just the chemistry name. The published description is high-purity low-density dilute sulfuric acid at 1.24 ± 0.01 g/cm³ when fully charged. Confirm the specified density for float service on the cell datasheet and the recommended topping-up water specification, because using mains water with a high mineral content causes the deposits that shorten float life.

Check the cell consistency procedure. Cells from one production batch share a float-current signature. A string assembled from two months of production will show a divergence that looks like a charger fault. Ask how the supplier isolates production lots and whether cells are assembled into matched strings at the factory.

Verify the case, rack and vent design at delivery. A 77.00kg cell is not going to be hand-handled; a cracked case or a sheared φ20-M8 terminal is found at unpacking, and a bank that has been stacked on its ends in a container should not be accepted without inspection. A shipping damage protocol with photographic evidence at the port of discharge protects both sides.

Make the acceptance test real. The delivery note is not a test certificate. A 10-hour rate capacity verification on a sample string to 1.80V/cell, a recorded float current after 24 hours on float, an electrolyte density and level check on every cell, an inter-connection resistance check and a visual inspection of every cell should all sit in the acceptance protocol.

Require a spare-parts and inspection plan in the contract. A 2% spare-cell allowance with the bank, a recommended inspection interval for the actual ambient profile, and a written float-voltage schedule remove the two failure modes that account for most avoidable early replacements.

FAQ: Flooded Tubular Battery Questions Answered

Q1: How many OPzS2-1500 cells are needed for a 48V telecom plant?

Twenty-four cells in series give a 48V nominal bus floating at 53.5V, storing 72 kWh nominal per string. One string supports roughly 24 hours at a 50% depth of discharge for a 1.5kW load; two strings in parallel give 144 kWh and full redundancy while one string is isolated for maintenance.

Q2: How often do flooded tubular cells need water top-ups?

The interval follows ambient temperature and is far shorter in hot plant rooms — of the order of monthly in a 30–35°C environment and considerably longer in a cool one. The published float design life of more than 20 years assumes the electrolyte level is maintained; a flooded cell operated dry corrodes the positive grids regardless of how well it was manufactured.

Q3: What is the correct float and equalising voltage?

Float at 2.23V per cell at 25°C with −3mV/°C/cell compensation, equalising at 2.35V per cell, and cycling charge at 2.40–2.45V per cell. On a 24-cell string that is 53.5V float and 56.4V equalising. The maximum recommended charging current is 0.20 × C10 A, which is 300A for the 1500Ah cell.

Q4: Does a flooded battery room need special ventilation?

Yes. Flooded cells release hydrogen during charge, so the room must be ventilated and the calculation should follow EN 50272-2 and IEC 62485-1, with hydrogen monitoring above the cell vent line in larger rooms. Sizing ventilation from the cell count alone is a common and avoidable error.

Q5: How much capacity do I lose at higher discharge rates?

The 1500Ah rating is measured at the 10-hour rate to 1.80V/cell at 25°C. At the 3-hour rate the same cell typically delivers around 160–190Ah less, and losses grow further at the 1-hour rate. Autonomy calculations for ride-through duty must therefore use rate-corrected figures, not the 10-hour nameplate.

Q6: Is a flooded OPzS cell cheaper than a gel OPzV cell of the same capacity?

Usually yes on first cost — the OPzS2-1500 is published at 77.00kg against 104.00kg for the OPzV2-1500, and flooded cells are generally priced well below their sealed equivalents. The saving is partly given back through water top-up labour, a larger ventilation design and a heavier plant room, so compare on 7-year cost of ownership rather than on the quotation. The full tubular gel comparison is on the OPzV tubular gel battery range page.

Q7: What standards should the supplier certify?

For flooded tubular stationary cells, IEC 60896-11:2002 and DIN 40736-1:1985, with GB/T 19638.2-2014, YD/T 1360 for telecom backup duty, Eurobat Long Life classification, and BS 6290 Part 4 / UL 1989 where the UK or North American market is served. Ask for the conformity statement, batch date codes, a cell consistency procedure, and the CE, ISO 9001 and ISO 14001 documentation for the manufacturing site.

Q8: What does a proper acceptance test involve at delivery?

A 10-hour rate capacity verification on a sample string, a float current reading after 24 hours on charge, an electrolyte density and level check on every cell, inter-connection resistance and torque checks, and a visual inspection of every case and terminal for transit damage. Record the results before the consignment is accepted.

Q9: Which model should I choose instead of the 1500Ah?

The published range steps through OPzS2-1200 (62.50kg), OPzS2-1000 (53.50kg), OPzS2-800 (43.80kg) and OPzS2-600 (32.30kg) below the 1500Ah, and OPzS2-2000 (105.50kg), OPzS2-2500 (131.00kg) and OPzS2-3000 (155.00kg) above it, so cell size can be matched to floor loading, rack pitch and handling rules, with parallel strings used for the remaining capacity. Every cell in the range is 2V, so the string length at your DC bus is always fixed.

Q10: Is the OPzS2-1500 suitable for solar hybrid storage with daily cycling?

Yes, provided the charge profile is set to the published cycling voltage of 2.40–2.45V per cell rather than the float value, and the design is based on the published cycle life of 1,500–2,500 cycles at 80% DoD. In hybrid plants the battery sits on float through the dry season and cycles through the rainy or daylight hours, so the rectifier, the inverter charge controller and the maximum charge current of 300A per cell must be sized for the real daily profile.

Q11: How long will an OPzS2-1500 last in float service?

The published design life is more than 20 years at float, with a stated range of 20–25 years at 25°C. Real service life is shortened by high ambient temperature, missing temperature compensation, chronic undercharging and, above all, deferred water top-ups. Sites with a disciplined inspection routine and compensated float voltage are the ones that reach the two-decade figure.

Expert Summary

The published CHISEN OPzS2 range gives buyers a complete flooded tubular ladder — 100Ah at 9.20kg through 3000Ah at 155.00kg, all on a common 2V platform with 2.23V float charge, −3mV/°C/cell compensation, IEC 60896-11 and DIN 40736-1 conformity, and a float design life of more than 20 years. The OPzS2-1500 sits at the centre of that ladder at 1500Ah, 275 × 210 × 795mm, 850mm over the terminals and 77.00kg, and it is the cell most often quoted for 48V telecom plants, solar hybrid microgrids and MV/LV substation trip supplies across Africa, South America, South Asia and Southeast Asia. That combination of capacity range, dimensional transparency and published charge parameters is what makes flooded tubular the standard answer in those markets.

The economics are not automatically favourable, and buyers should be clear about that. On a 48V, 72 kWh nominal site the 7-year cost of ownership is roughly USD 5,600 for flooded tubular against USD 10,150 for tubular gel, USD 16,500 for AGM VRLA and USD 17,100 for lithium once the DC bus changes, cooling and BMS integration are priced in. Flooded tubular wins where the plant room already has hydrogen ventilation and a technician visit cycle; it loses where the site is unattended or the ambient temperature swings without compensation.

For procurement teams the operative conclusion is straightforward: specify the OPzS2-1500 against rate-corrected capacity for the actual discharge, set the rectifier to 2.23V per cell with compensation enabled and a 300A current limit, size the ventilation from the gas rate rather than the cell count, budget the water top-up routine as a line item, and run a genuine acceptance test including electrolyte density and level on every cell before the consignment is signed for.

Download the OPzS2-1500 Datasheet, Sizing Worksheet and Audit Checklist

Flooded tubular installations fail on three things: an autonomy figure with no discharge rate attached, a ventilation design that ignores the gas rate, and a water top-up routine that nobody budgeted. CHISEN supports specification and procurement with the full published OPzS series data, cell-level conformity documentation and a DC plant sizing worksheet.

Download Datasheet — the OPzS2-1500 technical datasheet with cell-level electrical data, dimensional drawing and the complete 16-model OPzS series table: OPzS2-1500 product specifications

Sample Inquiry — request a 48V string configuration for your site with the string layout, float and equalising setpoints, rectifier sizing basis and hydrogen ventilation calculation: https://wa.me/8613166226999

Supplier Audit Checklist — ask for the Supplier Audit Checklist covering cell consistency, batch traceability, transit damage protocol and acceptance testing: sales@chisen.cn

Send us your site load in watts, required autonomy in hours, DC bus voltage, ambient temperature range and the plant room ventilation situation, and our engineering team will return the string configuration, float and equalising setpoints, the rectifier sizing basis, the hydrogen ventilation calculation and a 7-year cost comparison — normally within 24 hours.

For the full OPzS flooded tubular range specification and series documentation: OPzS tubular flooded battery range

Source: CHISEN Battery published OPzS series specification data (IEC 60896-11:2002, DIN 40736-1:1985, EN 50272-2, IEC 62485-1, GB/T 19638.2-2014, YD/T 1360, BS 6290 Part 4, UL 1989); published CHISEN OPzV gel series data for comparative values; IEEE Std 450 guidance on battery plant design. Dimensions carry a published tolerance of ±2mm; weights and capacities apply at 25°C on the 10-hour rate. Cost bands are indicative 2026 mid-market values and are subject to volume, freight and certification scope. Verify all technical parameters with the CHISEN engineering team prior to a procurement decision.